Huawei OptiX OSN 580

Huawei OptiX OSN 580 Specification

Dimensions

221 mm (H) x 442 mm (W) x 224 mm (D)

Installation method

In a cabinet (including ETSI, 19-inch and 23-inch cabinets), in an outdoor cabinet

Switch capacity

Packet: 560 Gbit/s, TDM: 280 Gbit/s (higher order)

Packet: 280 Gbit/s, TDM: 280 Gbit/s (higher order)

Service slots

15 slots

Supported interfaces

OTN interface

OTU-2, OTU-3

Ethernet interface

FE/GE/10GE/40GE

SDH interface

STM-1/4/16/64

PDH interface

E1/E3; T1/T3

PCM interface

FXS/FXO, 2/4 wire audio and E&M

X.21/V.35/V.11/V.24/V.28, RS232/RS422, RS449/RS423A/RS422A, RS530/RS530A, RS485,

G.703 64 kbit/s bidirectional; IEEE C37.94

WDM interface

40 DWDM wavelengths, compliant with ITU-T G.694.1

8 CWDM wavelengths, compliant with ITU-T G.694.2

Networking Mode

Supports pure packet, hybrid (packet + SDH), or SDH networking

Supports WDM networking

Power Supply

-48 V DC/-60 V DC

220 V AC/110 V AC

Operation Environment

Temperature

 

Long term: -5ºC ~ 50ºC

Short term: -10ºC ~ 55ºC

 

Relative Humidity

Long term: 5% ~ 85%

Short term: 5% ~ 95%

Ethernet and MPLS-TP features

E-Line, E-LAN, and QinQ

MPLS-TP based VPWS and VPLS

MS-PW

ETH PWE3

IGMP Snooping v2

PCM features

 

Supports 64K cross connect

Voice or data conference, Point-to-Point, Point-to-Multipoint, Multipoint-to-Multipoint

FXO/FXS mode can be set by software

E&M signaling can be set by software (types I, II, III, IV, V and British Telecom SSDC5)

QoS

 

Hierarchical QoS scheduling and traffic shaping

DiffServ mode based on traffic classification

Simple traffic classification, complex traffic classification, per-hop behavior (PHB), and ACL

Committed access rate (CAR)

PQ scheduling priority, weighted round robin (WRR), and PQ+WRR queuing

Tail drop and weighted random early detection (WRED)

Shaping based on port scheduling priority

OAM

 

MPLS-TP OAM

 

CC, LB, LT

AIS, RDI

LM, DM

LCK, TST

CSF

 

Ethernet OAM

ETH-CC, ETH-loopback, ETH-link trace, remote loopback, remote fault detection, RMON (RFC 2819)

Protection

Equipment-level protection

1+1 backup for cross-connect, system control, clock processing board, and power unit

MPLS-TP-based service protection

LSP/PW linear protection, ring protection

Anti-multiple failure protection based on MS-PW

LAG, MC-LAG, Dual-homing protection, LPT, ERPS

SDH-/PDH-based service protection

Linear MSP and MSP ring

SNCP

E1 1+1 SNCP

E1/T1 1+1 tributary protection switch (TPS)

Synchronization

Supports G.813, Synchronous Ethernet, and IEEE 1588v2 synchronization

Adaptive clock recovery (ACR)

Two external clock inputs/outputs (2 MHz or 2 Mbit/s)

Two external time signals inputs/outputs (1pps+TOD)