Question 1

What is SFP+ For 3000 Series?

Accepted Answer

SFP+ For 3000 Series is a family of 10 Gbps small form-factor pluggable optical transceivers designed for high-performance switching and routing platforms in data center and enterprise networks.

Question 2

Which data rates does SFP+ For 3000 Series support?

Accepted Answer

SFP+ For 3000 Series supports a line rate of 10 Gbps, ensuring full-duplex transmission for applications such as 10G Ethernet, Fibre Channel, and high-speed interconnects.

Question 3

What fiber types and wavelengths are available?

Accepted Answer

SFP+ For 3000 Series modules are offered in single-mode (1310 nm, 1550 nm) and multi-mode (850 nm) variants, covering distances from 300 m to 40 km depending on the model.

Question 4

How far can SFP+ For 3000 Series transceivers transmit?

Accepted Answer

Depending on model and fiber type, SFP+ For 3000 Series modules support distances from 300 meters on OM3/OM4 multi-mode fiber to 40 kilometers on single-mode fiber.

Question 5

Are SFP+ For 3000 Series modules hot-swappable?

Accepted Answer

Yes. SFP+ For 3000 Series transceivers are hot-swappable, allowing insertion or removal without powering down the host device to minimize network downtime.

Question 6

Which devices are compatible with SFP+ For 3000 Series?

Accepted Answer

These SFP+ modules are certified for 3000 Series switches, routers, and NICs, and they interoperate with standard-compliant 10 Gbps interfaces from major vendors.

Question 7

How do I install an SFP+ For 3000 Series module?

Accepted Answer

Align the transceiver with the host port, gently insert until the latch clicks, then connect the appropriate LC fiber cable; the switch will automatically detect and enable the module.

Question 8

How can I verify compatibility before purchase?

Accepted Answer

Consult the 3000 Series hardware compatibility list or use the vendor’s online compatibility tool to confirm support for specific SFP+ part numbers and firmware versions.

Question 9

Can I mix single-mode and multi-mode in the same link?

Accepted Answer

No. To avoid signal loss and mismatch, both ends of a 10 Gbps link must use the same fiber type and wavelength, either single-mode or multi-mode.

Question 10

Is third-party sourcing allowed for these modules?

Accepted Answer

Yes. Third-party SFP+ For 3000 Series-compliant modules adhering to IEEE and MSA standards are supported, provided they pass interoperability tests with your hardware.

Question 11

What is the typical power consumption?

Accepted Answer

SFP+ For 3000 Series modules consume approximately 1 W to 1.5 W per port, depending on wavelength and operating conditions, ensuring efficient power use in high-density deployments.

Question 12

What temperature range do these modules support?

Accepted Answer

Standard SFP+ For 3000 Series transceivers operate between 0 °C and 70 °C; industrial versions extend that range from –40 °C to 85 °C for harsh-environment applications.

Question 13

How do I maintain and clean SFP+ ports?

Accepted Answer

Use lint-free swabs and isopropyl alcohol to clean the LC connector endfaces; cover unused ports with dust caps to prevent contamination and ensure optimal signal quality.

Question 14

How can I monitor module health and performance?

Accepted Answer

Leverage SFF-8472 digital diagnostic monitoring (DDM) via your switch’s management interface to track temperature, voltage, optical power, and transmit/receive bias current in real time.

Question 15

What warranty and support options are available?

Accepted Answer

SFP+ For 3000 Series modules include a limited lifetime warranty against defects and full technical support, with options for on-site replacement and advance swap expedites.

Question 16

How do I troubleshoot a non-working SFP+ link?

Accepted Answer

Verify module compatibility, inspect fiber connectors for contamination, check link LEDs, confirm matching wavelength and fiber type, then review switch logs for diagnostic errors.

SFP+ 3000 Series Modules

GLC-GE-100FX= (100FX SFP ON GE SFP PORTS FOR DSBU SWITCHES)

GLC-BX-D= (1000BASE-BX SFP, 1490NM )

GLC-BX-U= (1000BASE-BX SFP 1490NM)

CWDM-SFP-1490= (CWDM 1490 NM SFP GIGABIT ENET AND 1G/2G FC VIOLET)

CWDM-SFP-1470= (CWDM 1470 NM SFP GIGABIT ENET AND 1G/2G FC GRAY)

CWDM-SFP-1550= (CWDM 1550 NM SFP GIGABIT ENET AND 1G/2G FC YELLOW)

CWDM-SFP-1510= (CWDM 1510 NM SFP Gigabit Ethernet and 1G/2G FC )

CWDM-SFP-1570= (CWDM 1570 NM SFP GIGABIT ENET AND 1G/2G FC ORANGE)

CWDM-SFP-1610= (CWDM 1610 NM SFP GIGABIT ENET AND 1G/2G FC BROWN)

CWDM-SFP-1590= (CWDM 1590 NM SFPGB ENET AND AND 1G/2G FC RED)

CWDM-SFP-1530= (CWDM 1530 NM SFP GIGABIT ENET AND 1G/2G FC GREEN)

DWDM-SFP-6141= (DWDM SFP 1561.42 nm SFP (100 GHz ITU grid) )

DWDM-SFP-5736= (DWDM SFP 1557.36nm SFP (100 GHz ITU grid))

DWDM-SFP-5332= (DWDM SFP 1553.33NM SFP BUILD-TO-ORDER)

DWDM-SFP-4214= (DWDM SFP 1542.14 nm SFP (100 GHz ITU grid) )

DWDM-SFP-4931= (DWDM SFP 1549.32nm SFP (100 GHz ITU grid) )

DWDM-SFP-4532= (DWDM SFP 1545.32nm SFP (100 GHz ITU grid) )

DWDM-SFP-4134= (DWDM SFP 1541.35nm SFP (100 GHz ITU grid))

DWDM-SFP-3739= (DWDM SFP 1537.40NM SFP BUILD-TO-ORDER)

DWDM-SFP-3425= (DWDM SFP 1534.25NM SFP 100GHZ ITU GRID)

Questions & Answers

What is SFP+ For 3000 Series?

Which data rates does SFP+ For 3000 Series support?

What fiber types and wavelengths are available?

How far can SFP+ For 3000 Series transceivers transmit?