United States
Q
What is a Brocade SAN Compatible SFP CWDM transceiver?
A
A Brocade SAN Compatible SFP CWDM transceiver is a small form-factor pluggable optical module designed for Fibre Channel networks that uses Coarse Wavelength Division Multiplexing to carry multiple LAN or SAN channels over a single fiber link.
Q
Which wavelengths are supported by Brocade SAN Compatible SFP CWDM modules?
A
Brocade SAN Compatible SFP CWDM modules typically support ITU-specified wavelengths ranging from 1271 nm to 1611 nm in 20 nm increments, allowing selection of the appropriate channel for your CWDM network.
Q
Are Brocade SAN Compatible SFP CWDM transceivers hot-swappable?
A
Yes, Brocade SAN Compatible SFP CWDM transceivers are fully hot-swappable, enabling safe insertion or removal from a powered switch without disrupting other active ports.
Q
What data rates do Brocade SAN Compatible SFP CWDM modules support?
A
Brocade SAN Compatible SFP CWDM modules support Fibre Channel data rates up to 16 Gb/s, ensuring high-speed, low-latency performance for storage networks.
Q
Which Brocade switch models are compatible with SFP CWDM modules?
A
Brocade SAN Compatible SFP CWDM modules are validated on the Brocade G630, G610, G620, X6 Series, and all Gen-6 Fibre Channel switch families for seamless integration.
Q
How do I install a Brocade SAN Compatible SFP CWDM transceiver?
A
To install, power on the switch, align the LC connector, slide the SFP CWDM transceiver into the empty port until it clicks, then verify the link LED status in the switch fabric view.
Q
What is the maximum transmission distance of Brocade SAN Compatible SFP CWDM?
A
Brocade SAN Compatible SFP CWDM modules deliver up to 80 km of single-mode fiber reach, depending on the selected wavelength and fiber attenuation.
Q
Do Brocade SAN Compatible SFP CWDM modules require optical attenuators?
A
Optical attenuators are recommended only when link power budgets exceed transceiver receiver sensitivity, typically for distances under 2 km or over 40 km.
Q
How can I verify the wavelength of my Brocade SAN Compatible SFP CWDM?
A
Use a fibre optic power meter with wavelength detection or consult the switch’s diagnostic SFP info command to read the module’s encoded wavelength identifier.
Q
Are Brocade SAN Compatible SFP CWDM transceivers third-party certified?
A
Yes, these transceivers undergo rigorous Brocade qualification and interoperability testing to ensure compliance with MSA standards and Brocade fabric requirements.
Q
What is the typical power consumption of a Brocade SAN Compatible SFP CWDM?
A
Brocade SAN Compatible SFP CWDM modules consume less than 1 W of power under normal operation, minimizing impact on switch power budgets.
Q
Do Brocade SAN Compatible SFP CWDM modules come with a warranty?
A
Brocade SAN Compatible SFP CWDM modules are covered by a one-year limited warranty, with options to extend via Brocade support contracts.
Q
How do I troubleshoot link issues with Brocade SAN Compatible SFP CWDM?
A
Verify fiber cleanliness, check LC connector seating, confirm correct wavelength pairing, and use switch diagnostics to test bit error rate and receive power levels.
Q
Can I mix CWDM and DWDM transceivers in the same Brocade SAN?
A
Mixing CWDM and DWDM is not recommended on the same fiber pair due to differing channel spacings; use dedicated fibers or appropriate multiplexers for hybrid deployments.
Q
What environmental operating conditions do Brocade SAN Compatible SFP CWDM modules require?
A
Operating conditions are 0 °C to 70 °C temperature range, 5% to 85% non-condensing humidity, and compliance with RoHS and Telcordia GR-63-CORE standards.
Q
How do I ensure compatibility when replacing Brocade SAN SFP CWDM transceivers?
A
Match the exact wavelength, data rate, and form factor, verify the Brocade part number, and consult the Brocade interoperability matrix before deploying replacements.
